GearSource

MM4 Miniature Wide-Range Loudspeaker

$460.30 $460.30

The MM-4 loudspeaker is a very compact, wide-range loudspeaker for high quality distributed system applications. In contrast to conventional low power 70-volt transformer based systems, the MM-4 connects directly to the amplifier and is capable of producing high sound pressure levels while dramatically reducing distortion and easing installation requirements.

The MM-4 comprises a single 4-inch cone driver with a 16-ohm voice coil mounted in a sealed enclosure. The MM-4 draws 150 watts peak from the line, and produces 112.5 dB peak SPL. Typically, with four MM-4s connected in parallel on the line, the system requires a direct drive power amplifier capable of 600 watts continuous output (49 volts rms) into 4 ohms.

The MM-4CEU is a two-channel, single rack space unit providing frequency and phase response correction circuitry tailored to the MM-4 loudspeaker. Through a SpeakerSense connection to the power amplifier output, the MM-4CEU continuously monitors the power applied to the drivers, activating integral peak and RMS limiters to protect against over-excursion and overheating, respectively.

The MM-4CEU incorporates Meyer Sound’s MultiSense circuit to drive several amplifiers, monitor two amplifier channels and activate its protection circuits based on the system branch with the highest signal level. MultiSense allows the levels of individual zones to be adjusted using the power amplifier's attenuators. Typically, each channel of the MM-4CEU can drive 12 or more amplifier channels depending on the input impedance of the amplifier.

The MM-4 enclosure's black anodized extruded aluminum acts as a sink to dissipate heat from the driver voice coil. It can be ordered custom-painted to match décor, and is fitted with a perforated steel grille.

Two connector versions are available: the sealed EN3 connector for outdoor installations, and a Phoenix-style keyed connector for use indoors. A companion MUB-MM4 U-bracket is available for mounting that affixes to the cabinet with two 3/8"-16 screws and is drilled to fit an OmniMount bracket. An optional MMFA-MM4 flush mount assembly is available for ceiling or wall mount applications.

8 Available:   0 New | 8 Used

Stock Brands : Meyer  

View Listings:
Placeholder

Meyer Sound MM4

ID: 126710  
Condition: Good   
Warranty: 48 Hours
8 Available
Placeholder

Meyer Sound MM4

ID: 126710  
Condition: Good   
Warranty: 48 Hours
8 Available

DESCRIPTION

The MM-4 loudspeaker is a very compact, wide-range loudspeaker for
high quality distributed system applications. In contrast to
conventional
low power 70-volt transformer based systems,
the MM-4 connects directly
to the amplifier and is capable
of producing high sound pressure levels
while dramatically
reducing distortion and easing installation requirements.

The MM-4 comprises a single 4-inch cone driver with a 16-ohm voice
coil mounted in a sealed enclosure. The MM-4 draws 150 watts peak from
the line, and produces 112.5 dB peak SPL. Typically, with four MM-4s
connected in parallel on the line, the system requires a direct drive
power amplifier capable of 600 watts continuous output (49 volts
rms) into 4 ohms.

The MM-4CEU is a two-channel, single rack space unit providing
frequency
and phase response correction circuitry tailored
to the MM-4 loudspeaker.
Through a SpeakerSense connection
to the power amplifier output, the
MM-4CEU continuously
monitors the power applied to the drivers, activating
integral peak and RMS limiters to protect against over-excursion and
overheating, respectively.

The MM-4CEU incorporates Meyer Sound’s MultiSense circuit to
drive several amplifiers, monitor two amplifier channels and activate
its protection circuits based on the system branch with the highest
signal level. MultiSense allows the levels of individual zones to be
adjusted using the power amplifier’s attenuators. Typically, each
channel
of the MM-4CEU can drive 12 or more amplifier
channels depending on
the input impedance of the amplifier.

The MM-4 enclosure’s black anodized extruded aluminum acts as a sink
to dissipate heat from the driver voice coil. It can be ordered
custom-painted
to match décor, and is fitted with a
perforated steel grille.

Two connector versions are available: the sealed EN3 connector for
outdoor installations, and a Phoenix-style keyed connector for use
indoors.
A companion MUB-MM4 U-bracket is available for
mounting that affixes
to the cabinet with two 3/8"-16
screws and is drilled to fit an
OmniMount bracket. An
optional MMFA-MM4 flush mount assembly is available
for
ceiling or wall mount applications.